STEP 1 • HARDWARE WIRING

HC-05 / HC-06 / HC-08 to Arduino Pinout

Using SoftwareSerial on Arduino Digital Pins D10 (RX) and D11 (TX) lets you upload code over USB without unplugging your Bluetooth module every time.

Bluetooth Module Pin Arduino Uno / Nano Pin Notes
VCC 5V Most HC-05/06/08 breakout boards accept 3.6V–6V
GND GND Common ground between Arduino, BT & relays
TXD Pin D10 (Soft RX) Direct 3.3V logic output is read safely by 5V Arduino
RXD Pin D11 (Soft TX) Recommended: 1kΩ / 2kΩ resistor divider (5V → 3.3V)
Hardware Serial Tip: If you wire Bluetooth directly to Arduino Pin 0 (RX) and Pin 1 (TX) instead of D10/D11, temporarily disconnect RX/TX while clicking Upload in the Arduino IDE.
ARDUINO UNO / NANO 9600 Baud Serial 5V GND D10 (RX) D11 (TX) HC-05 / HC-06 / HC-08 Bluetooth Serial TTL VCC (3.6-6V) GND TXD RXD (3.3V lvl) Cross-connect Serial lines: Module TXD → Arduino RX (D10) and Module RXD → Arduino TX (D11)
MODULE SPECS

HC-05 vs HC-06 vs HC-08 Quick Reference

Module Bluetooth Standard Default Baud Rate Default Pairing PIN Best Use Case
HC-05 Bluetooth 2.0+EDR (Classic SPP) 9600 (AT mode: 38400) 1234 or 0000 Smart switchboards, multi-relay home automation, robotics
HC-06 Bluetooth 2.0+EDR (Classic SPP Slave) 9600 1234 Simple Arduino Uno/Nano starter relays & voice switches
HC-08 Bluetooth 4.0 BLE (UART Service) 9600 No PIN (Direct BLE Connect) Low-power IoT sensors, battery-backed smart controllers
STEP 2 • ARDUINO SKETCH

Multi-Relay + PWM Fan Speed Arduino Code

Upload this sketch to your Arduino Uno or Nano. It listens for single-character relay ON/OFF payloads (A/a, B/b, C/c) and fan speed commands (0–4) sent by button tap or Google voice command from Bluetooth Device Controller:

#include <SoftwareSerial.h>

// Bluetooth TXD -> Arduino D10, Bluetooth RXD -> Arduino D11
SoftwareSerial btSerial(10, 11);

const int RELAY_1 = 7;   // Room Light   (ON: 'A', OFF: 'a')
const int RELAY_2 = 8;   // Socket       (ON: 'B', OFF: 'b')
const int RELAY_3 = 12;  // Garden Pump  (ON: 'C', OFF: 'c')
const int FAN_PWM = 9;   // PWM Fan Pin  (Speeds: '0' to '4')

void setup() {
  Serial.begin(9600);
  btSerial.begin(9600); // Default baud rate for HC-05, HC-06 & HC-08

  pinMode(RELAY_1, OUTPUT);
  pinMode(RELAY_2, OUTPUT);
  pinMode(RELAY_3, OUTPUT);
  pinMode(FAN_PWM, OUTPUT);

  // Active-HIGH defaults (invert HIGH/LOW if using Active-LOW relay boards)
  digitalWrite(RELAY_1, LOW);
  digitalWrite(RELAY_2, LOW);
  digitalWrite(RELAY_3, LOW);
  analogWrite(FAN_PWM, 0);

  Serial.println("Bluetooth Device Controller Ready!");
}

void loop() {
  if (btSerial.available() > 0) {
    char cmd = btSerial.read();
    Serial.print("Received Command: ");
    Serial.println(cmd);

    switch (cmd) {
      case 'A': digitalWrite(RELAY_1, HIGH); break;
      case 'a': digitalWrite(RELAY_1, LOW);  break;

      case 'B': digitalWrite(RELAY_2, HIGH); break;
      case 'b': digitalWrite(RELAY_2, LOW);  break;

      case 'C': digitalWrite(RELAY_3, HIGH); break;
      case 'c': digitalWrite(RELAY_3, LOW);  break;

      // Fan Speed Commands
      case '0': analogWrite(FAN_PWM, 0);   break;
      case '1': analogWrite(FAN_PWM, 70);  break;
      case '2': analogWrite(FAN_PWM, 130); break;
      case '3': analogWrite(FAN_PWM, 190); break;
      case '4': analogWrite(FAN_PWM, 255); break;
    }
  }
}
STEP 3 • APP CONFIGURATION

Matching App Buttons & Voice Phrases to Your Sketch

Creating ON/OFF & Fan Buttons

  1. Open Bluetooth Device Controller and pair/connect to your HC-05, HC-06, or HC-08 module.
  2. Open Buttons Setup and add a new button.
  3. Enter a friendly label (e.g., Room Light), set ON command to A and OFF command to a.
  4. For fans or dimmers, configure speed levels mapped to 0, 1, 2, 3, and 4.

Voice Phrases & JSON Backup

  1. Save a custom voice phrase for each action (e.g., "light on" → A, "light off" → a).
  2. Tap the Microphone icon on the controller screen and speak your phrase clearly.
  3. To back up or copy your layout to another phone, tap Home Menu → Export buttons to file to save a portable .json file.